In order to participate in the GunBroker Member forums, you must be logged in with your GunBroker.com account. Click the sign-in button at the top right of the forums page to get connected.
Smith & Wesson Recall
rufe-snow
Member Posts: 18,650 ✭✭✭
Posted 21 February 2009 07:36 AM
Smith & Wesson has identified a condition that may exist in certain PPK and PPK/S pistols which may permit a round to be discharged without the trigger being pulled. When the manual safety is disengaged, Smith & Wesson's Product Engineering Group has determined that the possibility exists in certain firearms that lowering the hammer may cause a chambered round to fire.
DESCRIPTION OF THE PRODUCT INVOLVED:
This recall applies to all Walther PPK and PPK/S pistols manufactured by Smith & Wesson from March 21, 2002, until February 3, 2009. The Serial Numbers of the pistol subject to this recall are as follows:
BAB 0010-BAB 9999
BAC 0000-BAC 9999
BAD 0000-BAD 9999
LTD 0000-LTD 0499
PPK 0001-PPK 1500
BAE 0000-BAE 9999
BAF 0000-BAF 9999
WLE 0001-WLE 0459
BAH 0000-BAH 9999
BAJ 0000-BAJ 9999
BAK 0000-BAK 9999
REP 0026-REP 0219
BAL 0000-BAL 5313
BAM 0000-BAM 1320
REMEDY/ACTION TO BE TAKEN:
STOP USING YOUR PISTOL AND RETURN IT TO SMITH & WESSON AT ONCE.
Any unintended discharge of a firearm has the potential for causing injury, and we ask that you stop using your pistol immediately.
To facilitate the repair of your pistol, please contact Smith & Wesson's customer service department to receive instructions for the return of your pistol to Smith & Wesson.
When you return your pistol to Smith & Wesson, we will replace the existing hammer block feature with a new part at no cost to you. Your firearm will be returned as quickly and efficiently as possible.
VERIFICATION OF CORRECTIVE ACTION:
When your pistol is returned, you should note a punch dot which appears at the back
Smith & Wesson has identified a condition that may exist in certain PPK and PPK/S pistols which may permit a round to be discharged without the trigger being pulled. When the manual safety is disengaged, Smith & Wesson's Product Engineering Group has determined that the possibility exists in certain firearms that lowering the hammer may cause a chambered round to fire.
DESCRIPTION OF THE PRODUCT INVOLVED:
This recall applies to all Walther PPK and PPK/S pistols manufactured by Smith & Wesson from March 21, 2002, until February 3, 2009. The Serial Numbers of the pistol subject to this recall are as follows:
BAB 0010-BAB 9999
BAC 0000-BAC 9999
BAD 0000-BAD 9999
LTD 0000-LTD 0499
PPK 0001-PPK 1500
BAE 0000-BAE 9999
BAF 0000-BAF 9999
WLE 0001-WLE 0459
BAH 0000-BAH 9999
BAJ 0000-BAJ 9999
BAK 0000-BAK 9999
REP 0026-REP 0219
BAL 0000-BAL 5313
BAM 0000-BAM 1320
REMEDY/ACTION TO BE TAKEN:
STOP USING YOUR PISTOL AND RETURN IT TO SMITH & WESSON AT ONCE.
Any unintended discharge of a firearm has the potential for causing injury, and we ask that you stop using your pistol immediately.
To facilitate the repair of your pistol, please contact Smith & Wesson's customer service department to receive instructions for the return of your pistol to Smith & Wesson.
When you return your pistol to Smith & Wesson, we will replace the existing hammer block feature with a new part at no cost to you. Your firearm will be returned as quickly and efficiently as possible.
VERIFICATION OF CORRECTIVE ACTION:
When your pistol is returned, you should note a punch dot which appears at the back