In order to participate in the GunBroker Member forums, you must be logged in with your GunBroker.com account. Click the sign-in button at the top right of the forums page to get connected.
Why all the ?? marks?
D@D
Member Posts: 4,407
Why all the question marks in the "Installation Instructions" part? They must not be to sure how to install there own product LOL. Not to mention its hard to read, guess there webmaster wasn't an English major. Must have out sourced to India.[:p][:D]
"CAUTION! Improper installation or use may result in damage property, severe injury, or loss of life. If for any reason this product does not function properly, discontinue use immediately. Always practice proper handling techniques, safety precautions, and ensure an UNLOADED condition. Cut tubing (EMT) to desired length with any standard hack saw. Ensure cut is square and that you do not crush or deform tubing if holding in vise. Carefully deburr and smooth both inside and outside diameters of cut with file or sand paper. Measure 3/8? from end of tubing and mark hole center placement on centerline of tubing. Carefully drill 9/32? diameter hole through one side of tubing and deburr. (If tubing is out-of-round it may be necessary to use some degree of force to insert the Bayonet Adapter and seat it properly.) Insert adapters large end into tubing and line up adapter tapped hole with drilled hole in tubing. Gently tap adapter with soft hammer or rubber mallet until adapter flange is against end of tubing. Install one of the supplied ?-20 x 3/8? Button Head Cap Screws through drilled hole, into tapped hole and tighten with supplied hex wrench. (The adapter is designed to have a tight fit with the bayonet and should require some degree of force to seat properly. If the fit is loose, it may be necessary to very slightly collapse the hole in the bayonet by gently compressing it in a bench vise.) Install your bayonet onto the tapered end of the adapter by aligning the engraved area of the adapter with the slot in the bayonet. Gently tap bayonet onto adapter with soft hammer or rubber mallet until threaded hole in adapter is in the center of the ?square? opening in bayonet. Depress locking mechanism of bayonet and install second supplied ?-20 x 3/8? Button Head Cap Screw into tapped hole in adapter and tighten with supplied hex wrench. Check for proper tight fit."
http://brassstacker.com/mosin-nagant/Mosin-Nagant-9130-Bayonet-Adapter-MN-BA.html
"CAUTION! Improper installation or use may result in damage property, severe injury, or loss of life. If for any reason this product does not function properly, discontinue use immediately. Always practice proper handling techniques, safety precautions, and ensure an UNLOADED condition. Cut tubing (EMT) to desired length with any standard hack saw. Ensure cut is square and that you do not crush or deform tubing if holding in vise. Carefully deburr and smooth both inside and outside diameters of cut with file or sand paper. Measure 3/8? from end of tubing and mark hole center placement on centerline of tubing. Carefully drill 9/32? diameter hole through one side of tubing and deburr. (If tubing is out-of-round it may be necessary to use some degree of force to insert the Bayonet Adapter and seat it properly.) Insert adapters large end into tubing and line up adapter tapped hole with drilled hole in tubing. Gently tap adapter with soft hammer or rubber mallet until adapter flange is against end of tubing. Install one of the supplied ?-20 x 3/8? Button Head Cap Screws through drilled hole, into tapped hole and tighten with supplied hex wrench. (The adapter is designed to have a tight fit with the bayonet and should require some degree of force to seat properly. If the fit is loose, it may be necessary to very slightly collapse the hole in the bayonet by gently compressing it in a bench vise.) Install your bayonet onto the tapered end of the adapter by aligning the engraved area of the adapter with the slot in the bayonet. Gently tap bayonet onto adapter with soft hammer or rubber mallet until threaded hole in adapter is in the center of the ?square? opening in bayonet. Depress locking mechanism of bayonet and install second supplied ?-20 x 3/8? Button Head Cap Screw into tapped hole in adapter and tighten with supplied hex wrench. Check for proper tight fit."
http://brassstacker.com/mosin-nagant/Mosin-Nagant-9130-Bayonet-Adapter-MN-BA.html
Comments
Merc
It is an ASCII character that isn't being interpreted correctly. That is all.
Merc
That's interesting.
Will that fit on my Ar15?
Eventually, yes, it will fit just fine!
Brad Steele
Will that fit on my Ar15?
Not sure, give them a call. 828-665-4427