In order to participate in the GunBroker Member forums, you must be logged in with your GunBroker.com account. Click the sign-in button at the top right of the forums page to get connected.

scope mounts

vette81vette81 Member Posts: 177 ✭✭✭
edited October 2010 in Ask the Experts
hi

i am putting a scope on a new rifle.a friend said to use high mounts.now i always mount my scopes as close to the barrel as i can get.always thought that would be more acurate.Listening to my friend i was curious if it matters?Thinking about triing it but it does not seem like it would be beneficial to me.woundering what othere people think. thanks for the time.

mib

Comments

  • vette81vette81 Member Posts: 177 ✭✭✭
    edited November -1
    WHO MAKES SCOPE MOUNTS FOR A COLT LIGHT RIFLE AND DOES ANYONE KNOW THE ITEM # OF THE MOUNTS THANKS
  • vette81vette81 Member Posts: 177 ✭✭✭
    edited November -1
    Got a really great deal on a New England Handi Rifle in .308. It had a Simmons scope on it with a set of see through mounts. Real akward to see through the scope with that mount. Want to mount a Weaver K4 on it. Suggestions as to a good mounting system. Keep in mind I'll need clearance for the hammer.

    By the way.......what can I expect to pay for a 20 guage shot gun barrel for it?
  • vette81vette81 Member Posts: 177 ✭✭✭
    edited November -1
    hi, is there any specific things i need to consider when mounting my scope? is there any areas i should avoid or anything that would matter or affect anything?, i am mounting a nikon buckmasters 6-18 on my ruger 77/17.any information is appriciated,

    Thanks,
    Martin Janczak
  • vette81vette81 Member Posts: 177 ✭✭✭
    edited November -1
    Does anyone know anything about pop off scope mouts?? the ones like they use in the military, where you can take the scope off to store it, and then snap it back on?? are they accurate? Where can you find them?


    * r DONE
  • vette81vette81 Member Posts: 177 ✭✭✭
    edited November -1
    I purchased a Rem. 700 and it came with scope mounts. Does anyone use these or is it a recommended practice that I just go out and purchase better ones?
  • vette81vette81 Member Posts: 177 ✭✭✭
    edited November -1
    I just mounted a 3x9-50 scope on a Optima elite with Belgarra barrel. My guestion is how close is too close for the scope bell and barrel clearance? It clears the barrel by 1/16".[:D]
  • vette81vette81 Member Posts: 177 ✭✭✭
    edited November -1
    I have a Browning (Japan) 1885 rifle with 24" half octagon barrel.
    The receiver and barrel are factory drilled & tapped for mounting
    a scope.
    Can anyone tell me which bases and/or mounts will fit this rifle.
    I haven't been able to find information specific to this rifle.
    Thanks for any help or suggestions on this !
  • vette81vette81 Member Posts: 177 ✭✭✭
    edited November -1
    Where can I get standard scope mounts to go on a
    1959 Mannlicher Schoenauer. NOT CLAW MOUNTS
    I want to mount a standard leupold scope
    write to traveler6@mwpower.net
    Thanks
  • vette81vette81 Member Posts: 177 ✭✭✭
    edited November -1
    I bought a savage modle110 from my brother he had someone put a scope on it .I have shot around 500 rounds thru it and can't get the scope sited in when I took of the scope and mounts I noticed that the front holes and the back holes do not line up they are off by about an 1/8th of an inch . does anyone make a scope mount or ring that would adjust to fix this problem??? please help!!![?]
  • vette81vette81 Member Posts: 177 ✭✭✭
    edited November -1
    was wondering if rifles such as winchester 70, remington 700..etc that are pre-drilled and tap for scopes are all uniform, so that it i decided to buy a weaver or leupold mount it would work on all.
  • vette81vette81 Member Posts: 177 ✭✭✭
    edited November -1
    I HAVE AN ENFILED 303 AND AN M-44 IN 7.62X54R RIFLES I NEED TO KNOW WHAT KIND OF BASE MOUNTS WOULD FIT THE BEST? I STILL HAVE TO DRILL AND TAP BOTH GUNS,OR DOES IT MATTER WHAT KIND SINCE I HAVE NOT DRILLED AND TAPED THEM?
  • vette81vette81 Member Posts: 177 ✭✭✭
    edited November -1
    Hi I'm new here and it looks like I may get my question ansered here i hope. as I'm posting this for my brother, he was wondering if he could put scope on a 303 british jungle carbine ? and if so where can he get the mounts ? and the cost ? thanks to all that reply.
  • vette81vette81 Member Posts: 177 ✭✭✭
    edited November -1
    suggestion for a 99 ARISKA scope mount. Already drilled and tapped.
  • vette81vette81 Member Posts: 177 ✭✭✭
    edited November -1
    I need advice. I have a scope mounted on a Remington MOdel 700 that is shooting at least 8 inches high at 25 yds with the elevation cranked all the way down. I am using Luepold bases and medium height rings, would changing to low mount Luepold rings bring down the point of impact enough to make it useableat say 100 yds?? I am still getting very tight groupings, just way too high

    Nil Illegitimus Carborundum
  • vette81vette81 Member Posts: 177 ✭✭✭
    edited November -1
    Does anyone manufacture 1" Scope rings that will clamp onto a standard .22 grooved rail approx 1/2" wide?
    Make and approx price?
  • vette81vette81 Member Posts: 177 ✭✭✭
    edited November -1
    New to mounting a scope. I ordered a set of leupold rings and bases and they don't fit, the rings are dovetail and the bases are standard which leads me to my question. Which is better, the dovetail with no windage base adjustment or the standard with the windage base adjustment. I am mounting a leupold scope and leupold says that their scopes have enough built in adjustment that you don't need the base windage adjustment. Any commments.
  • vette81vette81 Member Posts: 177 ✭✭✭
    edited November -1
    will the rings on a muzzelloader handel the recoil of a 7 mm rem mag
    the reason I ask is I have a muzzelloader that the rings will work perfect on my 7 mm
  • amblerrlamblerrl Member Posts: 177 ✭✭✭
    edited November -1
  • guntech59guntech59 Member Posts: 23,187 ✭✭✭
    edited November -1
    If it's not touching, it's fine.
  • vette81vette81 Member Posts: 177 ✭✭✭
    edited November -1
    Thanks guys,[:D]
  • deerhntrdeerhntr Member Posts: 1,853 ✭✭✭✭✭
    edited November -1
    I mount them as close as possible, if you can slide a dollar bill under it you are good to go
  • 1KYDSTR1KYDSTR Member Posts: 2,361 ✭✭✭
    edited November -1
    I agree but would rather see something more like a 1/32" clearance minimum...always fear flex under recoil whether that is a reasonable consideration or not!
  • beantownshootahbeantownshootah Member Posts: 12,776 ✭✭✭
    edited November -1
    quote:Originally posted by vette81
    I just mounted a 3x9-50 scope on a Optima elite with Belgarra barrel. My guestion is how close is too close for the scope bell and barrel clearance? It clears the barrel by 1/16".[:D]


    You're good to go.

    Basically, you want the scope

    -As low as possible, such that
    -It doesn't actually touch the barrel/receiver, and
    -It still lines up well with your eye.
  • wpagewpage Member Posts: 10,201 ✭✭✭
    edited November -1
    With a big objective lens like a 50 mm you want it tight. Otherwise casing it is a problem.
Sign In or Register to comment.