In order to participate in the GunBroker Member forums, you must be logged in with your GunBroker.com account. Click the sign-in button at the top right of the forums page to get connected.
Options

thompson contender

tazzertazzer Member Posts: 16,837
edited September 2006 in Ask the Experts
Hello, i bought a very
early 1st gen contender,
sweet gun, engraving, nice
grips but the trigger is frozen,
won't even wiggle.All else works
did bubba get
a hold of this pistol?
· Share on FacebookShare on Twitter

Comments

  • Options
    tazzertazzer Member Posts: 16,837
    edited November -1
    [/size=3Hello,

    I just purchased a old Model Contender by TC, it is after 195,000 serial#. It is very stiff opening up this gun,does anyone have any thoughts about loosening this up ?

    Thanks
    · Share on FacebookShare on Twitter
  • Options
    tazzertazzer Member Posts: 16,837
    edited November -1
    Hello,

    Can anyone explain the difference between Contender & g2 Contender ?

    Thanks
    · Share on FacebookShare on Twitter
  • Options
    tazzertazzer Member Posts: 16,837
    edited November -1
    Does anyone know when S/N 3066xx would have been mfg. Thanks JC
    · Share on FacebookShare on Twitter
  • Options
    tazzertazzer Member Posts: 16,837
    edited November -1
    Thompson makes a barrell that fires 410 shotshells and 45 Colt. A 454 also fires 45 Colt. Does this indicate that a Thompson barrell will also fire the 454?

    JC
    · Share on FacebookShare on Twitter
  • Options
    tazzertazzer Member Posts: 16,837
    edited November -1
    Any one know where to get a schematic on the old style contender? This frame has been to the factory without any fixing the problem. I seem to have problems explaing to the young lady that when the hammer falls it does not hit the firing pin. hammer needs to fall 1/16 inch more to hit firing pin. Repair list that was returned stated firing pin replaced and checked ok. It does not check ok in Alabama. Anyone have suggestion of the problem. JC
    · Share on FacebookShare on Twitter
  • Options
    tazzertazzer Member Posts: 16,837
    edited November -1
    Ok i know this is a beaten dead horse but I have a [?][?][?]
    about the how the fram is register I am looking at a 223 that is a rifle and will be wanting to change it over to a pistol from time to time I emailed the dealer and asked how it was reg. and he emailed me
    that with a form 4473 the FFL can check Rifle or Handgun.
    is this so or does it need to be register as a pistol from tc[?][?]
    thanks
    Taz
    · Share on FacebookShare on Twitter
  • Options
    tazzertazzer Member Posts: 16,837
    edited November -1
    Ran into a guy that says he gas one in 454 casull. I can't find that in my blue book. Is he blowing smoke? If not, anyone know what it might be worth in like-new condition?

    Thanks,

    cbxjeffIt's too late for me, save yourself.
    · Share on FacebookShare on Twitter
  • Options
    tazzertazzer Member Posts: 16,837
    edited November -1
    Just bought a Thompson Contender G2 pistol.My question is will the front hand guard fit the 10" and 12" barell or do I need to purchase one for each barell?I also would like to scope a couple of barells for it.Do the barells come pre drilled for scope.This is my 1st contender so I could use any info on it.I am going to go with the 12" and 14" barells only.Thanks for any info. Al[?]
    · Share on FacebookShare on Twitter
  • Options
    tazzertazzer Member Posts: 16,837
    edited November -1
    My dad gave me this good looking pistol with a 357 barrel and the leopold scope. Sure is pretty. Not a scratch on it. How would you you rate the quality of this firearm? I'd never sell it, but is it worth anything?
    · Share on FacebookShare on Twitter
  • Options
    mbsamsmbsams Member Posts: 1,076 ✭✭✭✭✭
    edited November -1
    I don't think you will get many answers untill you rewrite your question in a way that can be understood.
    · Share on FacebookShare on Twitter
  • Options
    brier-49brier-49 Member Posts: 7,040 ✭✭✭✭
    edited November -1
    NO. as long as you do not leave the rifle stock on with a pistol barrel; shorter than 16".
    · Share on FacebookShare on Twitter
  • Options
    MIKE WISKEYMIKE WISKEY Member, Moderator Posts: 9,976 ******
    edited November -1
    it has to be manufactered as a pistol, you would have to check with the original manufacterer. if it was a rifle it cann't be changed to a pistol (you could get permision to make a "short barreled rifle" out of it).
    · Share on FacebookShare on Twitter
  • Options
    dfletcherdfletcher Member Posts: 8,162 ✭✭✭
    edited November -1
    Call T/C with the make & serial #. They should be able to inform you if it was manufactured as a rifle or handgun. If it's the old model Contender - Couger on the side, no easy open device & has a hammer mounted safety-there's a good chance it's a handgun. But again, call T/C & find out.
    · Share on FacebookShare on Twitter
Sign In or Register to comment.