In order to participate in the GunBroker Member forums, you must be logged in with your GunBroker.com account. Click the sign-in button at the top right of the forums page to get connected.

50 bmg

tatercatstatercats Member Posts: 711 ✭✭✭✭
has anyone wildcatted the 50 bmg yet? just wonderin.

tater

Comments

  • tatercatstatercats Member Posts: 711 ✭✭✭✭
    edited November -1
    I came across a website that listed some other powders for the 50 BMG beside the normal 50 BMG etc.. They were listing loads using common rifle powders. Anyone here try using more common powders in their BMG? Results?
  • tatercatstatercats Member Posts: 711 ✭✭✭✭
    edited November -1
    Amyone shoot or have any luck with cast bullets for 50 BMG
  • PinheadPinhead Member Posts: 1,485 ✭✭✭✭✭
    edited November -1
    Everything from .224/50cal.case up to and including a .70/50cal.case. There is very little in the wildcatting world that has not been tried by someone somewhere. I gave up the
    search years ago of trying to find something that on one had tried as yet. Waste of time and resources.
  • nononsensenononsense Member Posts: 10,928 ✭✭✭✭
    edited November -1
    tatercats,

    It has been wildcatted up and down the spectrum, just do some searches with a good search engine and haunt the wildcat shooting websites. Here is one that gained some notoriety:

    338/50 Talbot

    Historical Notes:

    The 338/50 Talbot is the work of Skip Talbot, Talbot's Custom Equipment in Fallon, Nevada. Skip began development of the cartridge in 1984 as an outgrowth of working with the 50 caliber Browning Machine Gun cartridge. The 338/50 is a 50BMG necked down to 338 caliber and with the shoulder angle increased to 35 degrees. The primary purpose of the 338/50 is long range target shooting out to 3000 yards. Forming dies are made by RCBS.

    General Comments:

    The 338/50 is a highly specialized cartridge and not intended for hunting. It would, of course, be adequate for any North American big game and the same would apply to Africa. The cartridge is over bore capacity and sever throat erosion occurred within only 250 rounds. Talbot also tried a shortened version of the cartridge, about one inch shorter than the full length case, in order to increase the loading density. The maximum load of 170 grains of Accurate Arms 8700 powder occupied only 77 percent of the volumetric capacity. However, the short version was not successful because muzzle velocity was reduced by about 500 fps. The full length case developed a muzzle velocity of 3700 fps with a 250 grain bullet when fired from a 44 inch barrel. By comparison, the 340 Weatherby Magnum pushes the 250 grain bullet at an initial velocity of 2850 fps from a 26 inch barrel, so the 338/50 develops an additional 850 fps with the same bullet. When one considers that, perhaps, 500 fps of the muzzle velocity results solely from a longer than standard barrel, these ballistics are not so impressive. However, with a much slower powder and bullets of 300 grains or heavier, the results might be spectacular. It is an interesting cartridge, but not very practical for most purposes.


    Source: Cartridges of the World




    338/50 Talbot Reloading Data

    Bullet (grs.) Powder / (grs.) MV ME Source
    250 SP AA8700 / 170.0 3700 7625 N/A
  • Tailgunner1954Tailgunner1954 Member Posts: 7,734 ✭✭
    edited November -1
    A couple others, the 700 Hubble Express is a 50BMG case that's had a belt swedged on and the neck streightened out, and there's the "12ga From *", which is a streightened 50bmg case that's had a rim put on to match the size of a 12ga rim.

    Whittemore
    Some guys like a mag full of lead, I still prefer one round to the head.
Sign In or Register to comment.