In order to participate in the GunBroker Member forums, you must be logged in with your GunBroker.com account. Click the sign-in button at the top right of the forums page to get connected.
Options
32-20 info
laogai
Member Posts: 309 ✭✭✭
a good friend wants me to reload for his 32-20 revolver, which i'm happy to do. however it seems that some used .312 bullets and some 308, but i don't know if that is true for both rifles and revolvers. i've asked him for more info and a photo but what i have now is this description:
"This revolver was my grandfather's gun that he used in the Tulsa Police Department. It says on the gun police select positive I believe. I will check more to make sure. It is a colt six shooter revolver."
he is mid-60's himself.
not too precise i know, and i'll post more info when received, but can anyone help me in selecting the correct bullet and load? will be used for casual plinking and any coyotes he may run across, so just a standard safe basic load is fine.
thanks
"This revolver was my grandfather's gun that he used in the Tulsa Police Department. It says on the gun police select positive I believe. I will check more to make sure. It is a colt six shooter revolver."
he is mid-60's himself.
not too precise i know, and i'll post more info when received, but can anyone help me in selecting the correct bullet and load? will be used for casual plinking and any coyotes he may run across, so just a standard safe basic load is fine.
thanks
Comments
His gun may be a Police Positive Special, but be sure that you see the barrel markings. There were several .32 rounds for this gun, so verify that .32-20 is correct for his.
I have a partial box of Winchester factory rounds. I will be glad to give them to you for your friend, as brass is difficult to find.
Neal
I don't post loads online because I can't see your weapon from here, a websearch will turn up some info. A Lyman or Lee cast bullet manual is a good thing to have even if you are using swaged bullets.
I have shot swaged .314 semi-wadcutters, but the group opened up to 3-4 inches.
Frank Barnes lists two revolver loads with 115gr. lead bullets pushed at:
5-gr Unique @ 980 f.p.s.
3-gr Bullseye @ 840 f.p.s.
Can't see how .308 diam. would benefit and cannot find any info using them? Your source?
The Colt should of course be marked the caliber as nmyers said, (and hats off for his offer), and Tflog uses the .312, but if in question can be barrel slugged easily enough.
EDIT: As Hawk stated, "...load levels listed in a recent handbook". Right. But there's the problemo-- hard to find for this round in handgun specs, or someone here would have already given? Which as since asked for I gave F. Barnes published load, while internet forums spout stuff all day long, (not that they are incorrect necessarily). Too, before posting I'd double checked my reloading manuals and the listed loads are in tune with other strickly .32 handgun cartridges. Of course, always start out 10% lower.
45er
To slug the bore, use a pure lead round ball for a 36 cal muzzle loader. Lube the bore well and drive the ball thru the barrel with a wooden dowel, from the muzzle to breech.
The dimensions of the lands and groove will tell you what diameter bullet you need to be shooting.
Best
EDIT 1
Over at the Hodgdon reloding site
http://data.hodgdon.com/cartridge_load.asp
They do have loads listed for the 32-20 in handguns. As I suspected, Trailboss is great for use in cast lead loads. I use it for everything from 38 special, to 41 magnum, 44 magnum, and 45-70 for cast bullet loads.
They use 0.312" diameter for jacketed bullets, and 0.314" diameter for cast bullets.
Best
As far as "recent handbooks" go, my Lyman 49th has .32-20 data.
I am a little leery about Barnes' CotW loads, they don't always say where they get their numbers. My present copy (12th edition0 doesn't have any pistol powder loads for it at all.
45r and Frank Barnes' 5 gr of Unique is heavier than Lyman or Ken Waters shows by a good deal, all they want is 4 grains with a 115 gr cast bullet. His 3 gr of Bullseye is OK by Waters but the current Lyman does not show Bull at all.
The stuff about .308" bullets is largely for things like Contenders that use a regular .30 cal barrel. Sometimes called the .30-20 to differentiate from the traditional Winchester/Colt guns.
if you wish you can send the shells to China Harvest, 4628 w central, wichita ks 67212,
316-942-8295
gar
here is one site that made the point about .312 cp .308, hence my concern: http://www.reloadammo.com/3220.htm
Thanks again
gar
I have loaded for a number of foreign made military revolvers over the years. Although they are chambered for metric cartridges of approximately 30 caliber, are 32-20 brass can be used for reloading. I use 3 grains of a fast burning powder with a burning rate similar to bullseye as a starting load, with bullets weights between 90 and 115 grains depending on bore diameter.
.308 should definitely be too small.
Don't use any loads meant for rifle or you will bulge chambers on Colt Police Positive or S&W Hand ejector K frame guns.
Single action Colts can handle heavy loads but these can't.
"The following is as good as I can read it.
Police special 32-20 WCF
Positive ( On the gun only one large P )
Colt's PTFA 1/ 1-000 Hartford Ct. USA
PATD AUG 5,1884 UNF6,1900 JULY4,1905
Serial number 329418
G"
just for informing those who've responded so helpfully, here are some details on the gun:
"The following is as good as I can read it.
Police special 32-20 WCF
Positive ( On the gun only one large P )
Colt's PTFA 1/ 1-000 Hartford Ct. USA
PATD AUG 5,1884 UNF6,1900 JULY4,1905
Serial number 329418
G"
Mine is marked the same, except for the ser# being 325xxx.
Mine has a 6in. barrel.