In order to participate in the GunBroker Member forums, you must be logged in with your GunBroker.com account. Click the sign-in button at the top right of the forums page to get connected.
Options
Reloading Question
dav1965
Member Posts: 26,543 ✭✭✭
what can i do to make my loads more accurate? have been thinking about turning the necks,using a neck bushing die,micrometer seating die an not crimping the case. am i on the right track or just wasting money
Comments
GH1[:)]
Can you only crimp bullets with a cannelure?? I'm thinking about getting the lee factory crimp dye. But i'm wondering if this will solve my problem.
Thanks for any advice.
I have a Sierra 3rd and 10th, Hornady 7th, Speer 10th, and Lyman 46th.
Are there any I don't have that I should get?
Also about how many 45 rounds would be in 1 pound of powder.
Also about how many 7 Mag rounds would be in a pound of powder.
Thanks David
I was full length resizing and decapping some .223 once fired brass.
I had previously cleaned it in stainless steel media.
I broke a decapping pin and thought maybe i had a crimped in primer? So i took a look at the case and this was not the case. so i replaced the pin and continued. About a dozen cases later same thing happens. So i look in the case and i see 2-3 stainless pins wedged in the bottom of the case. Heres the question: 1. What are the ramifications of the pins remaining in the case(I.E. missed when i decapped the case)2.Has anybody else had this issue? If so what is the remedy for correcting this...short of the obvious answer which is visually inspect every case or stop using S.S. media. Thanks for you help.
Every Cartridge in every gun is going to want a different powder for optamum performance, that powder may also change with bullet weights. For example, in my 10" 223 Contender the barrel likes Benchmark for 40-50gr bullets, but prefers VV N130 for 50-55gr. The most accurate load in this pistol is 25.0 gr of Benchmark with a 50gr Berger HPFB, I enjoy showing rifle shooters that smaller is better with that load.
1 pound of powder = 7000 gr, so if you are loading 75gr of 4831 in your 7mm Mag you will be able to load 93 rounds for a pound of powder. But with only 64.5gr of H450 you will be able to load 108 rounds.
Same with your 45acp, 10gr of Bluedot will give you 700 rounds while you could load 5gr of Bullseye and get 1400 rounds per pound. But you will really see a savings in loading your 9mm with 125gr cast bullets and 3.2gr of 700X, that load will give you 2187 rds per lb.
All of your rifle cartridges take Large Rifle primers, depending on the powder you use in the 7mm Mag you might need Large Rifle Magnum primers.
I can't over state load data enough.[:)] Check, check, and check, again.
If you are reloading used ammo make sure you sort out the small primer cases. If you try to put a large primer into a small hole, you may try to force it in and cause it to go boom.
The advice to read several reloading books first, is spot on.
Good Luck, and have fun. [:)]
I use H4831SC & H1000 for a large portion of my loads.
I run from ~59-70 grains in all the different loads.
7000gr/#
7000/70gr max=100 loads
7000/59gr min=~118 loads
I've used AA#7 for 9mm(about 850-900 loads per pound) and 40 S&W and the manual says it works for 45 ACP. Titegroup is a low dose(up to 1500 or more per pound), economical pistol powder but you MUST be careful of a double charge.
Like the others said, divide 7000 by the grains of powder in your load to get loads per pound.
If you want ONE all-around powder for your handguns, Unique fits the bill.
All of these powders have tons of verified and published data for just about any bullet weight you desire.
As was posted; 7000 grains are in a pound, so divide your load and you'll get a pretty good idea how many rounds can be loaded.
My 7mm Rem Mag loads range from 130gr-162gr.
I use H4831SC & H1000 for a large portion of my loads.
I run from ~59-70 grains in all the different loads.
7000gr/#
7000/70gr max=100 loads
7000/59gr min=~118 loads
Theoretically, but if you are using a powder measure mounted on the press, don't let the powder drop below 1/3 of the container or you may find the weight of the loads changing.
What is your definition of best powder? Best accuracy or best velocity?
9x19 (9mm Luger, 9mm Parabellum): Silhouette, WSF, and Power Pistol are excellent. 231/HP38 is accurate. Blue Dot and AA7 will give best velocity.
.40 (.40S&W): AA5 is most accurate. Silhouette is best at near max.
.45 (.45Auto, .45ACP): most accurate in all my .45s is 231/HP38 followed by AA2. True Blue is good at near max.
.270 (.270 Winchester): 4831 (either H or IMR)
.30-06: IMR4064 for accuracy. 4831 (either H or IMR) for max velocity
7mm Mag (7mm Rem Mag): 4831 (either H or IMR). Reloder 25 for max velocity
.30-30: IMR 4064 or H335 or BL-C(2), though Leverevolution is the one for max velocity
All the handguns can be quite happy with 231/HP38.