In order to participate in the GunBroker Member forums, you must be logged in with your GunBroker.com account. Click the sign-in button at the top right of the forums page to get connected.
Options
Wildcat 12GA From Hell.--
This discussion has been closed.
Comments
has picked up to finish. The fellow who started building
it laid it aside for awhile and the guy is going to finish
in BMG. It has 50cal bbl on it. Looks easily big enough
for 12ga,10ga,8ga, my 700s. The lever on left is cocking
mechanism, The tube in back is a firing striker and spring
and it hits the hammer block you see in the back of the
breach block, which hits firing pin ahead of it in breach.
I think firing setup can be compacted and streamlined,
which would make it easier to mount a stock,
It is the only one like it. And the first guy put
a lot of work in it.Ed
Co, PH action setup in my 700H 3.25" case. Fired
test load of 825gr at 3000 fps. This was just one
test load. Normal max loads are 825gr at 2850 and
1000gr at 2700.Hunting loads 24-2500, First PH fired
outside the factory.It is in first picture.
PH will work for any big case and my 585HE.And
if anyone looking at big actions for 12ga FH,
here is picture of MRC PH with a 3.5" 12ga case
partly into action. The PH cam be used for 12ga with
action and rails opened like I did my 700H in Enfield.
And a little changing on the bolt face and extractor
In 12 ga it still would have 60% of front lugs contacting
and you'd add bearing lug surface to bolt handle base so
it would handle same pressures as Savage 210.
And 3.5" with average length 12ga slug would feed from the
magazine. Our longer case would work with port opened
and some mag work. Ed
my 700H 3.25 in PH. I fit a bolt action 12ga
box mag and its follower and spring
inside the PH mag box. Easy to fit in metal box,
and permanently mounted to metal and floorplate.
Holds 2 down. That way feed lips already a working
design. And opened back of 12ga box for longer case
like I did with my 700 in Savage 210. Also work
for anyone doing a PH in 12ga FH if they aren't
loaded too long or with 3.5" RMC cases. Here is picture
PH from the bottom showing its size.You can see in pic
there still is room to make box longer yet.
And the feed port can be longer.Ed
Barrel 32" long, 1.87" breech, gun is 27 lbs.
Notice breech block is down and huge hole in barrel.
Maybe shoulder cannon is the right term for it.
It is all inleted into thumbhole laminated Vulcan
50 cal stock, of which I need more, if anyone
knows where there are any...Ed
showing a 2000ge slug protuding out. Simulating
stop action photo work, as if anyone was brave
enough to put a camera out in front of it
when it fired. Will have it firing by fall.Ed
Many guys want loads for 3" chambered slug barrels as they
come from the factory., So I put extra 24" Savage barrel I had
on a Mauser GEHA bolt action. Rifled Savage barrel is modern
steel with .93" muzzle diameter. Original barrel on the GEHA
was only .82" at muzzle. I added an extra rear bolt locking lug
onto the Mauser bolt. Using up stuff to make test gun.
Any modern steel slug barrel, whether on bolt, autoloading,
pump, or break action gun with same muzzle diameter will handle
these RE-17 loads. Max loads were all 115gr of RE-17 in plastic
3" cases, all with seals and cushion wads. Can't get no more under
the seals, cushions and slugs in 3". Which is why I like 3.5"
chambers. With 437 gr Brenekkee and 420 gr in BPI sabot got
over 1900. With 520gr Lyman in shot cup 1850. With 600gr Dixie
got 1800. With 870 gr hard lead got 1600. This is 24" barrel,
so longer barrels will get more. In comparison to IMR4227 loads,
these are about the same speed as using 90gr of 4227. But this
powder is so much easier on cases and guns, with about .004"
less base cup expansion. It works great in 3" and really gets the
speed in 3.5" cases, as in 3.5" cases,as seal/wads about same,
extra length for powder. The 870gr load is max peak pressure of
16,000 psi. Muzzle pressure is about 3500-4000 psi.
I'll have pic of the Mauser in few days.ED
It is 28ga FH, a 3.25" long brass case. Was a
12ga with light barrel. I also have a heavy 12ga
barrel chambered for 3.5" cases and a .500" barrel
for my 499HE a real long brass case. Also I am
doing my 499HE in a NEF. You can get a NEF with
MMouse 500S&W and run my reamer in and get real
power.The 395,495,595 actions will work also,
as they like the 695 have double bolt lugs
and a loading port that can be lengthened.Ed
12ga smooth bores and if they take high
speed. Well they'll do just as good at high
speed as the locked on wad stablized Brenekkee
OK slug I tested in my smoothbore 1887 with long
barrel, in first pic. Second pic is a Corbin
finned slug I will get and test later. Third is
BPI AQ slug I will test, few weeks in the 87.
I'm going to test also in a regular smooth bore
12ga slug barrel of medium muzzle size.Ed
setup with an Savage 210 rifled barrel. Used a Savage
plastic stock also. It is setup with the original 3"
chamber. I have many guys who want ideas and slug/load
combination's tested in regular rifled slug barrels, so
this is the one. Most testing will be 3" plastic cases.
Barrel 24" long, .93" regular slug size muzzle diameter.
The GEHA was originally converted from 98 Mausers in
Germany in the 20s, by reaming out all the front lug seats
and using the rear safety lug. I added a second rear
bearing lug and it handles 15,000 psi loads ok.
The cases come out with the weight of the bolt.
That will be max pressure used in it, with that slug gun
barrel thickness. Example load is 115gr of RE17 in 3"
plastic case, with 520 gr Lyman slug at 1850 plus fps.
This load expands the plastic case basecups about .005",
in comparison, a REM factory Buckhammer expands .010".
And we have over 300 fps more velocity.Ed
slugs in the red WIN wadcup in 3.5" plastic
case. Tested in rifled long barrel on the
NEF about 2100 fps. Greg Sappington makes
these. They are hollow point. 3" group at
50yds, peep sight, bad eyes. I also fired
a couple to see if they'd work in my long
brass cased 16GA FH shown in the picture.
They work ok, so Greg has a double duty
slug.They'd work in 16ga plastic also.
The 16ga was held at 1500 as the barrel
isn't super heavy, on the Stevens 16ga. Ed
up in power from 3.5 plastic, you can get 3.5" brass cases
from Rocky Mtn Cartridge. Here you can see how heavy
and nice they are compared to regular brass cases.
They also make shorter 3" brass cases also.
They fit the chamber tight and are long enough to
get some serious thumping power.And they have a
super strong, thick , solid head, not a weak balloon head
like regular ones on the left in pic.Ed
full length resize the case, only top 1/4 of case.
325gr at 2600, 500gr at 2150.
In NEF got both weight bullets 300 fps faster,
still extracted very easy.I got reamer. Just run it
in NEF 500 chamber and you got a blaster. And add
a little weight and thick pad to the gun.Ed
is heavier than most all add on pump gun barrels,
and it is 25.5" long, Something that would really get
it on with the slower powder loads we have.
Rifled barrel is solid mount in receiver, scoperail solid mount.
It is the REM 870 Super Slug Gun.
Nice long heavy barrel, and thumbhole stock for
handling recoil better. Plastic case 3" slug loads of ours that
gets 600gr slugs to 1800-1900 fps, work great in this
Like the ones I load and roll crimp in second picture
that are setting behind the little vise, and the one in the
vise readt to be crimped...Ed
the front, and a locked base and seal. Metal never
touches the bores. Work in great rifled and fair in
smooth barrels. These are steel, but copper would do
great also.Could be made heavier and different points.
On the net- ammunitiontogo.com
This one is about 500 gr.
Second picture is the 499HE to use in redoing the 500S&W,
shown on the also, in single shots, etc,for much more
power at 40-50% lower pressures.Ed
3", 3.5" 12ga plastic, 3.5 and 3.85" brass. I like it the
best of all, including using the real slow powders in our
long case with BMG primer.
Following tested in Savage-max pressure 35k psi.
I took couple of our first made 3.85" BMG based
long cases and bushed them back to use shotgun primers
to fire off the RE17. Works great, with 715gr jacketed slug
and 220 gr RE17 getting 2700 . With 420 gr slug in
BPI sabot with 250 gr RE17 getting 3200 plus.
Following tested in NEF-max pressure 25k psi.
Using 3.5" MRC brass, 715gr jkt and 200gr RE17, got 2500.
420 gr in BPI sabot and 220 gr Re17, got 2900 fps.
And we get real good velocities in plastic with half the
basecup expansion of factory mag loads.So that solves
problem-IE, being able to use regular firing mechanisms and
shotgun primers, with large enough powder charges to
get hairy velocities at mag shotgun pressures in plastic
and higher in brass cases with heavy barrels.A good powder
for plastic and brass loads.
I see now that Lightfield Co has the Commander 3.5" Plus
slug loads with 600gr at 1900, probably in a test barrel.
But that is great, seems we're being copied!!!ED
Here is an interesting combination slug available in Europe
and they are working to get distributors/stores here.
Any interested stores and shops contact them. We need
many sources of saboted slugs for reloading. The sabot
petals discards completely as slug exits muzzle and locked
on base stays with slug, making it nose heavy so it will give
decent accuracy in smooth bores.Will work in rifled barrels
also. Slug is .629" diameter, comes in 570gr, 700gr, 970gr
weights. They're selling these reloader/other loaders only.
It is called the US-S slug, and their site is
europeancartridgeunlimited.com ..Ed
I had helped him test another slug a while back.
He sent me some each of the US-S 570 gr, 700 gr, 970 gr.
I tested the 570 gr so far and in 3.5" plastic case in the 1887
smoothbore 35" barrel and in the NEF rifled 36" barrel at
1900 fps. I got that with 130gr of RE17 with one BPGS
seal under the sabot on the slug. The bottom of the sabot seal
is exactly like a BPGS, so a BPGS added gives double sealing.
Both smooth and rifled gave 3 shot 3" group each at 50 yds with
peep sights and bad eyes. This slug does as good as advertized
in smooth barrels, and smooth accuracy is as good as rifled.
My smooth barrel is tight, measuring 723" at muzzle.
These should be a great deer and hog slug. Folks need to get
after their dealers to work to import these for them..
On another note we may have found a guy who is gearing up
to make 10 ga rifled barrels. I'll know later this winter
If so I will put one on a bolt action and use the
10GA FH case I made or get from RMC..Ed
with other 12ga slugs I'm testing. Lefteris was
kind enough to send me a few of each weight
to test. They are the 3 in second row on the right.
They are 570gr, 700 gr, 970 gr. I tested 570gr in
3.5" plastic so far. At 1900 in the NEF rifled, and
in the 1887 smooth barrel, got 3" group on both.
With peep sights an bad eyes.So the US-S slug
is great in smoothbores, as good as rifled. My
smoothbore on the 1887 is .723" bore at muzzle,
a nice tight fit for smooth slugs. The smooth
bores Lefteris tested them with are .722" muzzle,
and they've already killed 5 wild boars, one shot
kills with the 570gr slug. Also if anyone wants a
heavy smoothbore new 12ga barrel, .722" muzzle,
1.375" outside diameter to make a great slug
gun with slugs like these, and others like the
Brenekkes, I have spare one. It is 30", chrome
moly alloy, super strong, nice an shiny inside
and out. Plenty of metal for any contour.
Good for bolt guns like Savage,Mossberg.ED
up on the Montana Rifle Co PH action. It is singlestack with
feed lips similiar to 12ga shotgun clip style magazines I
had here. Works great, shown in first picture. Now it is longer
than 12ga mags, but same setup would do for feeding
long brass 12GA FH and lon MRC 12ga cases. In picture
case is ready to clear the mag lips,then rim pops up under
extracter as bolt is moving forward. Second picture is
the box used that I made out of two PH boxes. That allowed
for extra height and fit for singlestack and riveted together.
Used a Savage 210 12ga follower and spring. ED
in a 3.5" brass case, got a 2.5" 3 shot group
at 50 yds. Great slugs they have come up with
for smoothbores.
We on here talking about getting 10 rifled
barrels made, here is a picture of my 4.1" long
brass 10ga I made from 50cal Russian by putting
on a rim like the 12GA FH is built.Just a prototype,
third in picture. Later I'll get RMC to make some,
as it is much easier way. First in picture is
16GA FH 3.5" long, 2nd 12GA FH 3.85" long,
3rd 10GA FH 3.1" long, 4th 8GA FH 4.3" long.Ed
test a few loads in. I made it from 55cal belted
Boys case. I reduced belt diameter a little and left
the base the same, which is 12ga size.In picture
first is 55cal, second expanded to .620", third
expanded to .660"(16ga), then two 12 ga ones.
Next is our 12GA FH, and then a 12ga 3.5"
plastic case.A little work in long 12ga FH chamber
with a tool for belt step and it chambers. Ed
3 foot of wood slabs in a bundle. It has shed its plastic
base and it went through straight without tumbling.
This one is 570 gr fired at 2200 in RMC case.Ed
and waiting for parts now. Problem is getting
real small parts without CNC for bushed
firing pin with rebound spring. But it takes
time.
We will have swaged lead slugs
in a little while as my barrel is smooth. They
will be 1600gr hollowbase, when done,
a hundred of them at least.
Got wads and cards, shown in the picture with 4bore
cases and slugs. And my 2bore case for comparison
Also 12ga wads for comparison..Ed
write up in # 470 Nov/Dec International Ammunition
Journal. Page 10-11 by Zach Weighman, a
cartridge collector and gun nut friend.
Got a guy just figured out BMG case rim, and for a rim
puts on 12ga high base cup from a plastic case. He turns
base/rim of bmg case about .008" and use JB Kwik to hold
it on. Pushes it on with press. He removes base cup with
heat gun from plastic cases,
He is using RE17, so shotgun primers will work, and he
puts bushing in case for primer. Has bushing reamed so
the primer pocket protrusion on the base cup goes up inside
tight, as he pushes on the base cup. It'll fire ok and to size it
do like I do, I push case into open top die, and push it
back out from the top with a rod and hammer. That
way the rim don't get bent up. He says it saves a lot of
time not having to make rim pieces.
We will have more info and pictures next few weeks.Ed
use on to it in place of the original cushion seal.
I also cut shallow slots in the outside at the bottom
of the petals. Sabot opens much quicker and seems
along with BPGS seals under it to work ok without
damage, giving high velocities. In pic on left is regular
BPI sabot, behind is one I put a cushion on from a
Brenekke KO slug, and in front the one with Flexseal on.
The slug in it is one a guy casts at 440 gr and .504"
diameter, and works ok.
New info on my 499HE, from now on we will make cases
out of 450 #2 brass, as Jamisons has 3-4000 cases,
and it seems no one has the 475 #2 we used first.
Only slight case dimension change is the base .012"
smaller, all else is the same. I'm getting reamers redone
and will be able to use in couple weeks. Case will still have
plenty of taper to extract easy in singles, doubles,
falling blocks.etc.
And speaking of falling blocks I found one, and put my 585HE
in it, and it is big enough and has enough clearance to be used
for a 577NE, 600NE, long 20ga, my long 16ga FH,
the 700H, the 700HE. Cost no more than Ruger, with barrel
figured in. Will have pics
and info soon. Ed
my 585HE in. It didn't need any work on the
feed trough to feed. 585 case shown in it.
In fact the trough is big enough
and the action big enough for 600NE, 3.5" 20ga
brass, 3.5" 16ga FH brass, my 700 HE long case.
I reworked a NEF stock to it, as I'm not
a stockmaker.Nice action.2nd picture is
of the 16GA FH in the feed trough.Ed
700HE long case in it.This falling block is 1.5"
wide, with a 1.125" wide breach block.
The sides are .187" thick next to breach block.
This compares to about .165" say for a Browning
B-87, Win copy. The feed trough would work with
12ga size rim if some work was done on the top
of the hammer. This has a barrel thread length of
1.005", thread diameter of 1.125" for good
strength. Ed
600NE in the feed trough. Work great
chambered as a 3.5" 20 gauge, for
20 gauge 3.5" brass and plastic cases also.
Second picture is a 12GA FH case we made by
epoxying on a 12 ga base cup onto a bmg brass
case. Turned brass down .010" and pressed on base
with epoxy in it and when set base is on good.Ed
bmg case is to use the new Magtech brass
12ga cases made by CBC in Brazil.
BPI and others sell them for less than
a buck each. Being so short they aren't
in the 12ga FH category of generating power.
But you cut them off a quarter inch long, and
turn a BMG rim down to .715 diameter, push on the
Magtech base, with JB weld in the Magteck
base, and set up a squeeze collet to
crimp the Magtech base sides into the BMG
extractor groove. Crimp it in hard and tight.
And it uses large rifle primers.Fed Mag 215 best.
Other bmg case work needed is to put a chamfer
on the bmg primer pocket and drill out the
bmg primer pocket straight so that there is no
block to the primer gases coming out through the
Magtech flash hole. Chamfer back of rim a little.
These will handle
20,000 psi loads.Ed
It has a 3.5" 12ga chamber in a heavy 27" Pacnor barrel,
that he put in place of original. He also put in a Knoxx
spring/cam recoil absorbing butt plate in the hollow
Savage plastic stock. He replace the plastic parts of the
absorber with aluminum parts. It is shown without the boot
so you can see how it is in the butt.He also has an oversize
pad on it. He hasn't weighted the gun with anything else and
it shoots comfortable, even off the bench with loads that get
a 500gr slug in a BPI sabot over 3000 fps. He gets this speed
with BPI and 500 gr in 3.5" plastic cases. He also can use
3.5" RMC cases and our BMG based case, cut to 3.5"...Ed
swages the 8ga kiln cases down to regular 8ga size.
It swages the belt down and a turning tool I made
removes the sharp edge on the belt after swaging,
to make a smooth transition to the right size.
It does it 4 times faster than previous process.
My chamber on the NEF is set up so regular sizes fit
and loaded kiln cases with the belt step won't go in.
It works with both the REM 8ga cases from BPI and the
WIN 8ga cases from Precision Reloading, and the
WIN cases are only 44 bucks a hundred, primed.
The WIN cases have the same extra powerful primer
just like the REM cases. The REM cases are black
and the WIN cases a see through plastic. Both same
thick sides.Anyone needing cases worked over
contact me... Ed
oneshot--In my Savage I hold to 30,000 psi. Other two
guys with big Borchardt falling blocks can go
70,000. Cases will take pressures for many reloads,
as the following pic shows of one sectioned that I
fired 36 times.No sign of thinning at all. Ed.
I'd like to use that on a squirrel just to see if anything would be left
A switch barrel auto we are tested 3.5" 12ga
smoothbore USS-S slugs, with hopped up loads.
About as accurate as the other guns here. Also
I'm getting the auto set up in my 585 HE long
case.585 HE long case shown in the port.
Switching barrels only takes minutes. This 12ga
barrel about as heavy as the 210 Savage barrel.
It is originally a 3.5" 12ga autoloader I've reworked
the stroke and have a barrel extension coming to add
585 28" barrel. Gun is weighted, thick double pad.
We are going to see how mild 585 HE loads of
9,000 ft lbs work in autoloader.Ed
I want to thank you for all of the resaerch you've done, and for keeping the forum up to date on your ongoing prodject. You are definately a true pioneer in firearms and amunition development.It's a rare treat to get to watch the progress as it happens.
W.D.
getting stuff to do cases with reasonable time and cost.
So a breakthrough with a 10ga FH, is putting 10 gauge
basecups from plastic cases onto 50cal Russian brass to
make a 4.05" long 10ga. I expand case using my shellholder
on original rim, put in bushing for shotgun primer, which
fires of RE17, the turn case and rim a little, and slip
on basecup with epoxy inside. Then take a 200 dollar heavy
barrel NEF 10ga, and deepen chamber like mine is.
Here is picture with one beside a 12ga FH. The 12ga FH holds
max load of about 330 gr ball powder below a slug,
and the 10ga FH holds 420gr. I'm getting things set
to get a bunch of cases to do this. Whoopee.
Now anyone wanting any of my cases for their collection
I have a package of them all. Contact me.. ...Ed